soliten.blogg.se

Shrinkit v1.1
Shrinkit v1.1




shrinkit v1.1
  1. SHRINKIT V1.1 GENERATOR
  2. SHRINKIT V1.1 FREE

Due to it being exponentially based, it is a lot faster at charging up than Vaporizer. Similar to Vaporizer, it will reset after it shoots an enemy to its base damage. However, a big difference is that Raygunner's damage increase doesn't increase at a linear straight consistent pace but instead exponentially but no one is smart enough to know what means so look at the equation at the Stat Chart that is sketchy. The Raygunner is similar to Vaporizer before it received Armor Destruction. 7C is a darkened version of level 6, using Abyss Matter, and it resembles a more scary alien. Which is correct, as 7A, is an alien with two guns trying to obliterate the human race, and 7B is just a human. This could imply that A, that they are from another planet for whatever reason or B, they are just a human in a bad disguise. The Raygunner appears to be an alien with no face from another planet/world, but as you level it up it gets more human equipment and clothing, strange. Gas valve adjusting screw tight against plunger (see fig.The Raygunner is a late-game tower with 3 forms that grow in strength as it attacks against a single enemy, similar to Vaporizer.

SHRINKIT V1.1 GENERATOR

Gas valve adjustment screw not operating plunger (see fig.3).Įarth strip on spark generator not touching barrel stabilizer (see fig.5). Gas tight joints must be maintained always check the hose and connections for leaks before use.Įxcess flow check valve not primed (see fig.1). Blow dirt from inside the barrel at regular intervals as reduced air flow will cause overheating and an irregular flame. Maintenance – Must only be carried out by an experienced gas fitter.Ī regular drop of oil (as supplied) into the valve at the hose connection (see fig.7) will prolong valve life. If you have any problems or queries regarding your shrink system, please contact your supplier.

  • Suitable extinguishers should be available for immediate use at site of operation.įailure to comply to any of the above instructions, including tampering with or dismantling of the gun, will invalidate your warranty.
  • shrinkit v1.1

    The shrink gun should be operated in a well-ventilated area, to ensure good all-round airflow when shrink-wrapping.Some consideration should be given to the erection of non-combustible screens around the area of operation.The operator must ensure no objects will interfere with the operation of the shrink gun.

    SHRINKIT V1.1 FREE

    Area for shrink-wrapping must be oil, grease and dust free and clear of all combustible material.Location and Ventilation for Shrink-wrapping The mixer MUST be fitted a minimum of 19mm into the burner (see fig.8).ĭO NOT hold the gun in a vertical position when shrinking the top surface of an object as rising heat can cause an unstable flame.NEVER hold gun in the vertical position when shrinking top surfaces as rising heat can cause an unstable flame (*see illustration below).Always hang the gun up using the eyelet provided (see fig.6). MAKE sure gas supply has been turned off correctly and any excess gas has been burned off before leaving gun unattended.NEVER LOOK IN BURNER OPENING WHEN GUN IS CONNECTED.NEVER DIRECT GUN TOWARDS ANY OTHER PERSONNEL.Care should be taken to ensure the gas bottle is not pulled along by the hose.The gun should not be used in hazardous situations, i.e.NEVER use the system with a damaged hose, regulator etc.Always check the hose and connections for leaks before use, there is an aerosol spray ‘leak detection’ available or (a soapy liquid brushed on joints will quickly detect leaks). Be sure to use a gas bottle with vapour only withdrawal.Only trained personnel should operate the system.Instruction in the safe operation of system must be given before any person is permitted to use the equipment.Shrink-wrap Unit in Operation Hazards and Safety Instructions The trigger must be depressed to maintain the flame. It is possible that the gun will ignite with only one small squeeze of the trigger, especially if it is warm and the operator has had a small amount of practice. Point the gun towards a clear area of the floor and squeeze the trigger slowly. Inspect connections for leaks (see Safety Instructions point 4 below). Turn on gas and slowly press the excess flow check valve to charge the system with gas (see fig.1). Connect shrink gun to other end of hose (left hand thread) see fig.2. Connect regulator into gas outlet and hose to regulator (left hand threads) – see fig.1. All personnel must read the following operating instructions.īefore proceeding please check gas bottle outlet is clean as this is the most common cause of failure.






    Shrinkit v1.1